Skip to content

SILISILRTV-2 silicones

SILISIL RTV MF-Dura 32

2K Additive Silicone Shore A 32 (Brown-red, mixing ratio 1:1) — 2K additive silicone Shore A 32 for detailed mold making and pad printing molds.

Cured Color
Brown Red
Self-leveling
Yes
Density (g/cm³)
1.17
Uncrosslinked viscosity (mPa·s)
6000

  • Brand
  • Color hardened - brownish-red
  • Food contact
  • Shore hardness A (cured)
  • Self-leveling
  • Medical grade
  • Density (g/cm³)
  • Uncrosslinked viscosity (mPa·s)
  • Mixing Ratio
  • Pot life (min)
  • Demolding time (min)
  • Full cure (h)
  • Tensile strength (MPa)
  • Elongation at break (%)
  • Tensile strength (N/mm)
  • Curing type
  • Electrical Insulation
  • Container
  • Mixing Ratio
  • Temperature range (°C)
Your selection SILISIL RTV MF-Dura 32
General terms and conditions of business

HS Code: 3910.0000

SILISIL RTV MF-Dura 32 Sample Offer

Technical Data

Typical values, not a specification. The technical data sheet (TDS) is binding.

Product Information

Brand
SILISIL
Mixing Ratio
1:1
Curing type
Addition (Platinum)
Container
500g+500g, 1kg+1kg, 5kg+5kg, 10kg+10kg, 25kg+25kg
Mixing Ratio
1:1
Temperature range (°C)
-40°C to 200°C

Physical Properties

Cured Color
Brown Red
Self-leveling
Yes
Density (g/cm³)
1.17
Uncrosslinked viscosity (mPa·s)
6000

Electrical Properties

Electrical Insulation
Yes

Curing values

Pot life (min)
10
Demolding time (min)
90
Full cure (h)
24

Product Approvals

Food contact
Yes
Medical grade
No

Mechanical properties

Shore hardness A (cured)
A 32
Tensile strength (MPa)
4.5
Elongation at break (%)
370
Tensile strength (N/mm)
10
Keywords
  • Mold Making
  • SILISIL
  • Silicone
  • RTV-2
  • Swiss warehouse
  • Addition
  • Platinum
  • Prototyping
  • Swiss brand
  • 2K
  • Moulding / Toolmaking
  • Shore A 32

Product Description

SILISIL RTV MF-Dura 32 is a room temperature vulcanizing 2-component addition silicone (platinum crosslinking, RTV-2) from the MF-Mold & Form series — 2K addition silicone Shore A 32 for detailed mold making and pad printing molds.

The mixture is prepared in a 1:1 ratio by weight (tolerance ±5%). Pot life at 23°C is approximately 10 minutes, demolding after approximately 90 minutes, and complete curing after 24 hours. Temperature resistant from -40°C to +200°C.

Key property

Suitable for food contact in chocolate molds up to 70 °C — Addition system 1:1 by weight, addition cross-linking, low shrinkage and temperature resistant −40 to +200 °C.

SILISIL RTV MF-Dura 32 in figures
A 32
Shore Hardness
6'000
mPa·s viscosity
10 min
Pot life @23 °C
370 %
Elongation at break

What distinguishes SILISIL RTV MF-Dura 32

Vulcanization at room temperature
Curing at room temperature — no oven, no UV lamp, no special equipment required.
High tear strength
High tear strength — robust against mechanical stress during demolding.
No shrinkage
Low shrinkage upon addition curing — the mold is immediately dimensionally stable without waiting time.
High dimensional accuracy and precision
High dimensional accuracy — the shape retains its form even after prolonged storage.
Tested for chocolate applications up to 70 °C
Suitable for food use after appropriate certification testing — ideal for chocolate and confectionery up to 70 °C.
Good processing viscosity
Practical viscosity — flows well, but remains controllable in multi-layer applications.

What is SILISIL RTV MF-Dura 32 used for?

Chocolate and confectionery molds
Suitable for food contact up to 70 °C — precise molds for chocolates, pralines and tablets for manufacturers and professional patisseries.
Pad printing pads
Silicone tampons with excellent color transfer and dimensional stability — transfer the color from the printing plate to plastic, glass and metal parts in industrial marking.
Detailed small-series molds
Reproduction of intricate models with lettering, microstructures and sharp edges — jewelry, toy prototypes, decorative components.
Concrete and cast stone replicas
Highly compatible with cement formulations — paving stones, facade elements, decorative architectural parts in small series.
Undercuts and negative forms
Elongation at break of 370% and tensile strength of 10 N/mm allow for the demolding of complex geometries without damage.
Industrial Master Models
Low-shrinkage reproduction of master models for vacuum casting, resin casting and manual small-batch production.

Processing

1
Prepare the original
The surface to be reproduced must be clean, dry, and free of dust. The ideal processing temperature is 23 °C — cooler environments significantly extend pot life and curing time.
2
Homogenize and mix components
Stir base and catalyst thoroughly before use. Weigh out 1:1 by weight (tolerance ±5%). When mixing, thoroughly incorporate the walls and bottom of the container.
3
Vacuum degassing
De-aerate the mixture according to the processing instructions. Take into account the container size and available processing time.
4
Pour slowly into the mold
Pour from a height of approx. 30 cm in a thin stream into the deepest point — the silicone displaces air independently and reaches all undercuts.
5
Vulcanize and demold
At 23 °C, demolding is possible after approx. 90 minutes, with complete curing after 24 hours. Before the first pour, allow a 24 h "maturation phase" for maximum strength.
Data Sheets & Safety Data Sheet
Complete TDS and SDS in DE, EN, FR — view or download directly.
To the documents →

Important Notes

Avoid crosslinking inhibitors
Additive systems like MF-Dura 32 are sensitive to sulfur, amine, tin, and phosphorus compounds—especially latex gloves, modeling clay, adhesive tapes, and some paints. If in doubt, make a small test cast before use.
Storage and Shelf Life
Shelf life of at least 12 months in unopened original container when stored in a dry, cool place (10–25 °C). Consult the Safety Data Sheet (SDS) before opening.
Available containers
1 kg + 1 kg, 5 kg + 5 kg, 25 kg + 25 kg, 200 kg + 200 kg. Other container sizes available on request.
Compatibility
Compatible with polyurethane, epoxy, and polyester casting resins. For aggressive resins, apply a release agent to protect the mold.

Recommended accessories


Which MF silicone for which application?

SILISIL RTV MF-Dura 32 in direct comparison with related MF products in our range (MF = Mold & Form).

MF-Dura 32
Current Product
MF-Dura 30 →MF-Dura 35 →MF-Dura 40 →
Shore hardness A32?3340
Mixed viscosity6'000?7'5005'500
ColorBrown Red?TranslucentBlue
Pot life @23 °C10?2050

Frequently asked questions about SILISIL RTV MF-Dura 32

Practical application and design questions — answered by SILITECH.

SILISIL RTV MF-Dura 32 is a two-component (Shore A 32, brownish-red) additive silicone for chocolate and confectionery molds and related applications. It is a two-component Shore A 32 additive silicone for detailed mold making and pad printing

At 23 °C, the pot life is approximately 10 minutes and the demolding time approximately 90 minutes. Complete curing is achieved after 24 hours. Lower temperatures extend, higher temperatures shorten these times.

As an addition system, SILISIL RTV MF-Dura 32 is sensitive to crosslinking inhibitors: sulfur, amine, tin, and phosphorus compounds can locally halt vulcanization. Avoid latex gloves, sulfur-containing modeling clays, some adhesive tapes, and PVC plasticizers in the immediate vicinity of the mold. If in doubt, make a small test cast.

SILISIL RTV MF-Dura 32 is mixed in a 1:1 ratio by weight (base to catalyst), with a maximum tolerance of ±5%. Homogenize both components separately before mixing, then thoroughly incorporate them – including the container walls and bottom. Brief vacuum degassing of the mixture is recommended for pore-free molds.

SILISIL RTV MF-Dura 32 achieves a Shore A hardness of 32 (ASTM D 2240), a tensile strength of >4.5 N/mm² (ASTM D 412), an elongation at break of approximately 370% and a tensile strength of 10 N/mm (ASTM D 624).