Skip to content

SILISILRTV-2 silicones

SILISIL RTV MF Spray 25-10 Thixo

Thixotropic 2K addition silicone of the MF series — Shore A 25, 10 min pot life, non-sagging on vertical surfaces, 1:1 mixing ratio, ideal for wall molding and multi-layer constructions

Cured Color
Light blue
Self-leveling
Thixotropic
Density (g/cm³)
1.1
Uncrosslinked viscosity (mPa·s)
-

  • Brand
  • Color hardened - Light blue
  • Food contact
  • Shore hardness A (cured)
  • Self-leveling
  • Medical grade
  • Density (g/cm³)
  • Uncrosslinked viscosity (mPa·s)
  • Mixing Ratio
  • Pot life (min)
  • Demolding time (min)
  • Full cure (h)
  • Tensile strength (MPa)
  • Elongation at break (%)
  • Tensile strength (N/mm)
  • Curing type
  • Electrical Insulation
  • Certificates
  • Container
  • Packaging
Your selection SILISIL RTV MF-Spray 25-10 Thixo
General terms and conditions of business

HS Code: 3910.0000

SILISIL RTV MF-Spray 25-10 Thixo Sample Offer

Technical Data

Typical values, not a specification. The technical data sheet (TDS) is binding.

Product Information

Brand
SILISIL
Mixing Ratio
1:1
Curing type
Addition (Platinum)
Container
400g, 1kg+1kg, 5kg+5kg, 10kg+10kg, 25kg+25kg

Physical Properties

Cured Color
Light blue
Self-leveling
Thixotropic
Density (g/cm³)
1.1
Uncrosslinked viscosity (mPa·s)
-

Electrical Properties

Electrical Insulation
Yes

Curing values

Pot life (min)
9
Demolding time (min)
60
Full cure (h)
24

Product Approvals

Food contact
No
Medical grade
No
Certificates
RoHS, REACH

Mechanical properties

Shore hardness A (cured)
A 25
Tensile strength (MPa)
4
Elongation at break (%)
400
Tensile strength (N/mm)
20
Keywords
  • Mold Making
  • SILISIL
  • Silicone
  • RTV-2
  • Swiss warehouse
  • Addition
  • Platinum
  • Prototyping
  • Shore A 25
  • Swiss brand
  • 2K
  • Moulding / Toolmaking
  • Sprayable
  • Thixotropic

Product Description

SILISIL RTV MF-SprayThixo 25-10 is a room temperature vulcanizing 2-component addition silicone (platinum crosslinking, RTV-2) of the MF-Mold & Form series — Thixotropic 2K spray silicone Shore A 25 — stable on vertical surfaces.

The mixture is prepared in a 1:1 ratio by weight (tolerance ±5%). Pot life at 23°C is approximately 10 minutes, demolding after approximately 60 minutes, and complete curing after 24 hours. Temperature resistant from -40°C to +200°C.

Key property

Thixotropic and non-sagging — can be applied to vertical surfaces, ceilings, and sculptures without running. Ideal for on-site molding and restoration.

SILISIL RTV MF-SprayThixo 25-10 in figures
A 25
Shore Hardness
Thixotropic
Consistency
10 min
Pot life @23 °C
400 %
Elongation at break

What distinguishes SILISIL RTV MF-SprayThixo 25-10

Thixotropic consistency — stable
Remains in place on vertical surfaces without running off — On-site molding on walls, ceilings, sculptures is possible.
Pot life 10 minutes
Very short processing time — suitable for high-throughput production with short mold cycles.
Tear resistance 20 N/mm
Very high tear resistance — the mold withstands hundreds of cycles with abrasive materials without wear.
Elongation at break 400%
High elasticity — reliable demolding of complex geometries without damaging the mold or the original.
Brushable or sprayable
Can be applied with a brush OR syringe — flexible application for different geometries and quantities.
Mixing ratio 1:1 by weight
Weigh the components according to the specified weight and mix thoroughly.

What is SILISIL RTV MF-SprayThixo 25-10 used for?

Vertical and overhead impressions
Thixotropic consistency remains on walls and ceilings — reliefs, statue profiles, component replicas on the installed object.
Restoration and monument preservation
On-site molding of columns, facade reliefs and historical building components that cannot be removed.
Brush or spray application on sculptures
Brush on the first layer of detail, then spray on the supporting layer — a classic sculpting technique on a studio scale.
Component shapes without container
Stands independently — no box or support structure required, saving material and time for small and individual shapes.
Multi-layer coatings for thick molds
Tensile strength 20 N/mm at elongation at break 400 % — robust multi-layer forms for industry and crafts.
Mock-up and set-building replicas
Film sets, theatre stage designs and advertising mock-ups benefit from the mobile application without tools or form boxes.

Processing

1
Prepare the original
The surface to be reproduced must be clean, dry, and free of dust. The ideal processing temperature is 23 °C — cooler environments significantly extend pot life and curing time.
2
Homogenize and mix components
Stir base and catalyst thoroughly before use. Weigh out 1:1 by weight (tolerance ±5%). When mixing, thoroughly incorporate the walls and bottom of the container.
3
Vacuum degassing
De-aerate the mixture according to the processing instructions. Take into account the container size and available processing time.
4
Pour slowly into the mold
Pour from a height of approx. 30 cm in a thin stream into the deepest point — the silicone displaces air independently and reaches all undercuts.
5
Vulcanize and demold
At 23 °C, demolding is possible after approximately 60 minutes; complete curing takes 24 hours. Allow a 24-hour "maturation phase" before the first casting for maximum strength.
Data Sheets & Safety Data Sheet
Complete TDS and SDS in DE, EN, FR — view or download directly.
To the documents →

Important Notes

Avoid crosslinking inhibitors
Additive systems like MF-SprayThixo 25-10 are sensitive to sulfur, amine, tin, and phosphorus compounds—especially latex gloves, modeling clay, adhesive tapes, and some paints. If in doubt, make a small test cast before use.
Storage and Shelf Life
Shelf life of at least 12 months in unopened original container when stored in a dry, cool place (10–25 °C). Consult the Safety Data Sheet (SDS) before opening.
Available containers
1 kg + 1 kg, 5 kg + 5 kg, 25 kg + 25 kg. Other container sizes available on request.
Compatibility
Compatible with polyurethane, epoxy, and polyester casting resins. For aggressive resins, apply a release agent to protect the mold.

Recommended accessories


Which MF silicone for which application?

SILISIL RTV MF-SprayThixo 25-10 in direct comparison with related MF products in our range (MF = Mold & Form).

MF-SprayThixo 25-10
Current Product
MF-Spray 25-6 →MF-PuttyFast 38 →MF-Dura 30 →
Shore hardness A252538?
Mixed viscositythixotropic8'000(Play-Doh)?
ColorLight blueLight blueLight Violet?
Pot life @23 °C1063?

Frequently asked questions about SILISIL RTV MF-SprayThixo 25-10

Practical application and design questions — answered by SILITECH.

SILISIL RTV MF-SprayThixo 25-10 is a two-component (Shore A 25, light blue) addition silicone sealant for vertical and overhead impressions and related applications. Thixotropic two-component spray silicone Shore A 25 — non-sagging on vertical surfaces

At 23 °C, the pot life is approximately 10 minutes and the demolding time approximately 60 minutes. Complete curing is achieved after 24 hours. Lower temperatures extend, higher temperatures shorten these times.

As an addition system, SILISIL RTV MF-SprayThixo 25-10 is sensitive to crosslinking inhibitors: sulfur, amine, tin, and phosphorus compounds can locally halt vulcanization. Avoid latex gloves, sulfur-containing modeling clays, some adhesive tapes, and PVC plasticizers in the immediate vicinity of the mold. If in doubt, make a small test cast.

SILISIL RTV MF-SprayThixo 25-10 is mixed in a 1:1 ratio by weight (base to catalyst), with a maximum tolerance of ±5%. Homogenize both components separately before mixing, then thoroughly incorporate them – including the container walls and bottom. Brief vacuum degassing of the mixture is recommended for non-porous molds.

SILISIL RTV MF-SprayThixo 25-10 achieves a Shore A hardness of 25 (ASTM D 2240), a tensile strength of >4.0 N/mm² (ASTM D 412), an elongation at break of approximately 400% and a tensile strength of 20 N/mm (ASTM D 624).