Skip to content

BluesilRTV-2 silicones

BLUESIL ESA 7250 200 ml A + 20 ml B

Optically clear, high-strength 2K-Pt silicone potting compound (Shore A 52) for electronics potting, optoelectronics, and photovoltaic cells

Temperature range
-50 to 200 °C
Viscosity
1’200 mPa·s
Viscosity A
1’000 mPa·s
Pot life
40 min

  • Brand
  • Color cured - Transparent
  • Food contact
  • Manufacturer
  • Self-leveling
  • Medical grade
  • Uncrosslinked viscosity (mPa·s)
  • Mixing Ratio
  • Pot life (min)
  • Tensile strength (MPa)
  • Elongation at break (%)
  • Tensile strength (N/mm)
  • Curing type
  • Electrical Insulation
  • Number of components
  • Consistency
  • UV resistance
  • Mixing Ratio
  • Container
Your selection BLUESIL ESA 7250 200 ml A + 20 ml B 40-7250AB.KT.ML200
General terms and conditions of business

Internal reference: 40-7250AB.KT.ML200
HS code: 39100000

BLUESIL ESA 7250 200 ml A + 20 ml B sample offer

Technical Data

Typical values, not a specification. The technical data sheet (TDS) is binding.

Processing

Viscosity of Mixture
1’200 mPa·s
Viscosity Component A
1’000 mPa·s
Viscosity Component B
1’200 mPa·s
Pot life at 23 °C
40 min

Physical and thermal

Density (23 °C)
0.98 g/cm³
Temperature resistance (duration)
-50 to 200 °C
Peak temperature (briefly)
200 °C

Electrical characteristics

Dielectric strength
23 kV/mm
Volume resistivity
10¹⁵ Ω·cm
Dielectric constant ε (1 kHz)
2.8
Dissipation factor tan δ
0.001

Storage

Shelf life in original packaging
12 months
Storage Temperature
-10 to 30 °C

Product Information

Brand
Bluesil
Manufacturer
Elkem Silicones
Mixing Ratio
10 : 1
Curing type
Addition (Platinum)
Number of components
2K (two-component)
Consistency
Flowable
Mixing Ratio
1:1
Container
200 ml + 20 ml

Further Properties

UV resistance
Yes

Physical Properties

Cured Color
Transparent
Self-leveling
Yes
Uncrosslinked viscosity (mPa·s)
4

Electrical Properties

Electrical Insulation
Yes

Curing values

Pot life (min)
4

Product Approvals

Food contact
No
Medical grade
No

Mechanical properties

Tensile strength (MPa)
6.2
Elongation at break (%)
115
Tensile strength (N/mm)
4
Keywords
  • Silicone
  • ESA
  • BLUESIL
  • 2K Silicone
  • ELKEM
  • Swiss warehouse
  • Addition
  • Platinum
  • Complete kit
  • 1:1
  • workshop
  • Silicone gel
  • Electronics Encapsulation
  • Optically Clear
  • 200 ml

Product Description

Bluesil ESA 7250 A & B is an optically clear, high-strength 2K-Pt silicone potting compound (Shore A 52) for electronics potting, optoelectronics, and photovoltaic cells.

This product range comprises 2K polyaddition silicone elastomers with optical clarity for electronics encapsulation, optoelectronics, and photovoltaic cells — defined refractive index, high transparency. ESA 7250 is tailored to specific industrial applications — the key properties and areas of use are listed below.

High strength + optically clear

Bluesil ESA 7250 combines excellent mechanical properties (6.2 MPa tensile strength, Shore A 52) with optical clarity. 10:1 mixing ratio, 4-hour pot life, refractive index 1.406 — proven industry standard for optoelectronics and high-performance potting.

ESA 7250 in numbers
Optically clear
Transparent
Shore A 52
Hardness
6.2 MPa
Tensile Strength
4 h
Pot life

What sets ESA 7250 apart

Optically clear
Direct visibility of encapsulated components — suitable for visible connections.
High strength (Shore A 52, 6.2 MPa)
Robust vulcanizate — protects mechanically stressed components.
Low-viscosity mixture
4'000 mPa·s — easy to degas and pour.
Long pot life (4 h at 23 °C)
Careful processing even with large volumes.
Definitive refractive index
n=1.406 — suitable for optical applications with index step.
Superior heat resistance
+200 °C for short periods, suitable for many industrial applications.

What is ESA 7250 used for?

Electronics potting
Potting of electronic components with high mechanical protection.
Optoelectronic connections
Optical fiber coating with index step.
Photovoltaic cells
Insulation and protection of solar cells.
Mechanical-optical components
Where transparency AND mechanical strength are required.
Industrial sensor technology
Encapsulation of high-performance sensors.
LED potting
High-performance LEDs with clear optics.
Data Sheets & Safety Data Sheet
Complete TDS and SDS in DE, EN, FR — view or download directly.
To the documents →

Processing

1
Prepare the component
Position the component cleanly and dry in the encapsulation mold. Align the optical axes.
2
Mix A & B
10:1 or 1:1 (see comparison table). Low-viscosity mixture — easy to degas.
3
Degas
30–50 mbar vacuum — important for bubble-free optics.
4
Casting
Slowly pour into the mold — refractive index 1.40 makes the material optically clear.
5
Curing
24–48 h at 23 °C or accelerated with heat up to +150 °C.

Recommended accessories


Important Notes

Mixing & Dosing
Stir A and B thoroughly before each processing. Accurate dosing in the specified ratio (see table above) — preferably weight-based. Incorrect dosing leads to incomplete crosslinking.
Degassing
Degas the mixture under vacuum at 30–50 mbar. Material expands 3–4 times, falls back after 5–10 min. Interrupt vacuum several times for better degassing.
Avoid inhibitors
Polyaddition silicones are inhibited by: sulfur-vulcanized rubber, tin-catalyzed RTV, amine epoxides, PVC with tin salts. When in doubt, perform a preliminary test.
Application consulting
SILITECH advises you on the optimal RTV variant for your application — substrate, hardness, pot life, mechanics. Contact us with your specific application case.

ESA 7250 compared with related RTV products

Crosslinking system, mechanics, and processing times directly side by side — all values from the official Elkem-TDS. “— " = not specified in the data sheet.

ESA 7250
Current Product
RTV 141 →ESA 6110 →RTV 8352 LV →
Crosslinking system2K Polyaddition (Pt)2K Polyaddition (Pt)2K Polyaddition (Pt) Gel2K Polyaddition (Pt)
Mixing ratio10 : 110 : 11 : 11 : 1
ColorOptically clear, colorlessTransparent, colorlessOptically clearWhitish
Shore A hardnessA 52A 50Gel (penetration 250)A 55
Elongation at break115 %120 %—78 %
Tensile Strength6.2 MPa6 MPa—2.3 MPa
Tear strength4 kN/m———
Pot life4 h4 h50 min (Std) / 5 min (QC)130 min
Demolding time24–48 h24–48 h120–180 min8 h
Mixed viscosity4'000 mPa·s4'000 mPa·s1'200 mPa·s2'200 mPa·s
Main applicationElectronics pottingOptoelectronic connectionsElectronics Encapsulation (Potting)Electrical Engineering Encapsulation

Frequently asked questions about ESA 7250

Practical processing and design questions — answered by SILITECH.

Bluesil ESA 7250 A & B: Optically clear, high-strength 2K-Pt silicone potting compound (Shore A 52) for electronics potting, optoelectronics, and photovoltaic cells. Main applications include electronics potting, optoelectronic connections, and photovoltaic cells.

Polyaddition crosslinking is a 2-component silicone chemistry with a platinum catalyst. Component A contains the platinum complex, component B the SiH crosslinker. When mixed, the components crosslink without releasing reaction by-products — no shrinkage due to outgassing substances, excellent dimensional accuracy, low linear shrinkage. Important: Polyaddition silicones are inhibited by various substances — sulfur-vulcanized natural rubbers, tin-catalyzed RTV silicones, amine-catalyzed epoxy resins, PVC stabilized with tin salts. In case of doubt, a preliminary test must be carried out.

Thoroughly stir components A and B before each processing step. Dose precisely according to the mixing ratio specified in the TDS (see comparison table above) — preferably by weight. Mix with an electric or pneumatic stirrer at low speed (minimize air entrainment). Degas the mixture under vacuum (30–50 mbar) — the material expands to 3–4 times its volume, bubbles escape, and the material settles back after 5–10 minutes. Then pour slowly into the mold from the lowest point to avoid air entrapment. For polyaddition systems, avoid contact with inhibitors (sulfur rubber, tin RTV, amine epoxides, PVC with tin salts).

Store in unopened original container in a dry, cool place — typically between +5 and +30 °C, exact values see TDS. Store components A and B separately; after opening, seal airtight. Polyaddition systems are insensitive to moisture, but should be stored cool to preserve pot life. Consult the Safety Data Sheet (SDS) before use.

In the comparison table above, you will find related RTV products with different hardnesses, pot lives, or application profiles. If you are unsure about the optimal choice, we will be happy to advise you — contact SILITECH with your application (substrate, desired hardness, processing time, requirements for mechanical properties and resistance).